Toyota, Lexus & Subaru Tweeter Adapters | Laser-Cut to Your Tweeter
Laser-cut acrylic tweeter adapters for Toyota, Lexus, and Subaru - select your tweeter brand or cutout size
SKU: TYTweeterAdapters35mm
The one measurement that matters
Find your tweeter's flush-mount diameter.
This is the single number our adapter is cut to. It's the diameter of the mounting flange — the lip that sits against the panel — not the size of the dome you see. Get it from the manual, or measure it in 30 seconds.
- AOverall width
- BMounting-flange diameter — the one number we cut the adapter to
- CTotal height
- DMounting depth
Easiest · 9 times out of 10
Look it up in the manual
Almost every tweeter spec sheet lists it — look for “mounting diameter,” “flush-mount Ø,” or “cutout diameter” — often the dimension labeled B on the spec drawing. It's printed in the included manual and on the manufacturer's product page. That number is what you give us.
No spec sheet? · 30 seconds
Measure it yourself
Flip the tweeter over and lay a ruler or calipers across the back of the mounting flange (dimension B) — the flat lip that presses against the panel. Measure straight across the widest point, in millimeters. Ignore the dome in the middle entirely.
Don't measure the dome. A “1-inch tweeter” describes the driver, not how it mounts — the mounting flange is almost always larger. Two same-size tweeters from different brands can have completely different flush-mount diameters. The flange is the only number that fits the adapter.
Then choose it under Choose Your Tweeter Size above, or switch to the By cutout size (mm) tab. Our adapters are cut from 35 to 53 mm.
Pick your size aboveBuilt for the factory location.
Your component kit tweeters need a proper home. These laser-cut adapters put them in the factory tweeter location on your Toyota, Lexus, or Subaru for a clean install.
Check before you buy
Pre-cut for Focal, JL Audio, Kicker, Mosconi-Gladen, Audiofrog, and Arc Audio tweeters. Also available in 22 generic mm sizes from 35mm to 61mm. All brand names are trademarks of their respective owners and are used for compatibility reference only. Not sure which system you have? Ask us before you buy.
Full specifications
- Thickness
- 1/8 in (3 mm)
- Install Location
- Tweeter spot
- Tweeter Sizes (mm)
- 35 to 53
- Pre-Cut for Brands
- 6 brands
- Pre-Cut for Models
- 21 models
- Mounting Method
- No drilling
- Sold As
- Pair
The rest of the route, in one cart.
One part from each DIY step that fits your vehicle. Open any of them to choose its options and add it to your cart without leaving this page.
Owners adding an aftermarket amplifier who want a clean, no-drill install under the seat
20 ft of power + 20 ft of ground in 100% OFC Kicker wire, fused at the battery — 1/0, 4 or 8 gauge.
Toyota, Lexus, and Subaru owners upgrading factory front speakers to premium aftermarket 6.5-inch, 6x9-inch, or 8-inch drivers
2007-2021 Tundra owners upgrading factory speakers to premium aftermarket 6.5-inch or 8-inch drivers
Built in-house, start to finish.
Every adapter is designed and laser-cut under one roof in Mount Juliet, Tennessee. No outsourcing, no imported blanks - just solid acrylic, a laser, and people who care whether it fits right. Here's how a flat sheet becomes a pair of adapters cut to your exact speaker size.
Video - From the shop floor
Solid Acrylic
Every pair starts as a sheet of solid acrylic - flat, dense stock that holds a clean, precise edge, sized for the exact cutout your speaker needs.
Laser-Cut to Your Size
Each pair is laser-cut from our own files to your selected millimeter size - or pre-cut for brands like Focal, JL Audio, Kicker, Mosconi-Gladen, and Audiofrog - so your new speaker drops into the factory location.
Checked & Paired
Every adapter is checked against its cutout size and paired before it's packed. If it wouldn't go in our own truck, it doesn't ship.
Packed to Survive Shipping
Each pair is wrapped and packed by the same hands that cut it, so nothing arrives loose, scratched, or missing - and there's no extra hardware to lose, because the adapters mount with your factory hardware.
Everything customers actually ask.
The questions we get most on tweeter adapters - answered straight. Not sure if yours is here? Call, and a human answers.
One year, on everything we sell. Every item is covered for one year from delivery. If something fails in that first year, we make it right. Questions about a claim? Call us — a real person handles it with you.
Swap them in. Factory hardware, no drilling.
Every pair ships ready to install. The adapters mount with the factory hardware - follow the steps for your vehicle.
-
Remove factory trim panel covering tweeter location
-
Remove factory tweeter from mounting location
-
Place laser-cut acrylic adapter over factory mounting points
-
Secure adapter with factory hardware
-
Mount aftermarket tweeter into the adapter
-
Connect tweeter wiring
-
Reinstall trim panel
-
Repeat on the other side
How they hold up once they're installed.
Super easy process. Sent tweeter specs, they matched them with 51mm adapters. Perfect fit! Very Nice quality! Made installing a breeze. Highly recommend.
I bought these after trying a set from another maker. Those other ones were brittle and hard to drill screw holes in. These ones were pre-drilled and made of a non brittle material. Much much better. From now on, I’ll get all my brackets from sounds good.
These Tweeter mounts are a great solution to put aftermarket component speakers into your vehicle that uses factory component speakers. Just measure the tweeter body diameter, order the correct size, slip the tweeter through and mount them up. These worked perfectly in the A-pillars of my '19 F150 so I could run component front door and A-pillar speakers without having to do any wiring.
These adapters are absolutely perfect, and they made my install so easy. I highly recommend these!
For the most part they were just what I needed. Fitment was tight, with the help of the agent on the phone we were able to get the size fairly close. I had to take approximately another mm or two from the inner ring to slide the tweeter cup inside. What would be helpful is if the adapters came with bends at the connection locations. However, I'm fully aware every tweeter is different, smaller or larger so each application may vary. All in all they worked.
The adapters are nicely made. make it simple to put tweeters where the stock 3.25 inch stock speakers were. Thanks!
When installing speakers all over my expedition, I found certain speakers did not fit or accept the same size mounting even though they are advertised as the same "socket hole" -- 3 1/2 for instance. With SGS help I was able to overcome my front 2 corner speaker fitments and then with this product, I was able to fit my JL c7 3.5" center speaker with a PERFECT fit. I was so excited to see how well engineered the simple mount piece was -- and rigid! I was able to pop 4 screws and mount the speaker to the plastic piece SGS sent me and then put it into the center console space. It even aligned with the small helper pins to line it up with the factory screw holes and center the device perfectly as if it was OEM! I couldn't be more impressed! I am now looking at my rear mount speakers thinking I may pull the trigger again so I get everything just right. This needs to be advertised to those like me that a solution exists and it is not only affordable but well designed and executed! Thank you SGS one again!
These guys are legit, and so are their products. I have built 2 vehicles with them, and I can’t wait to do a third. Tweeter adapters are a perfect fit, and pair great with the SGS tweeter harness for that factory look. Thank you Don, Sage, and the rest of the crew.
These guys are doing big things and the help that this company was willing to provide and ensure I got my system close from as far away as I am is amazing! Don’t ever leave a review, the f-150 amp rack, wire harness and speaker adapters made it seem like I knew what I was doing! Great job SGS
These are compatible with several Chrysler vehicles, not just jeeps. Can be used in Challengers, Chargers, Ram 1500, 2500, 3500. Can also be used in Rams equipped with Harmon Kardon system to mount Tweeters in the door location. These are quality acrylic adapters and I used them to mount JL c7-350cm speakers in the dash locations in my Ram 1500. Just be careful drilling the pilot holes, I used a bit one size to small and the adapter cracked putting the screws in.
Needed a proper upgrade so ordered the Focal K2's and then ordered the tweeter adaptors. Adaptors fit perfectly and the hole for the tweeter was spot on. Way better than the janky alternative Crutchfield suggested with a strap. Super fast shipping as well!
Another great product from a great company. These fit perfectly for jeep and mopar vehicle with midrange in the corners of the dash. I'm running focal components in the front stage. WOW. Made the install easy. All questions were answered va phone and email prior to shipping. Fast and speedy arrival of product. Thanks again to sales team for answering the phone and talking to me about my specific questions I had prior to order.
The tweeter adapters were a perfect fit and made the installation of the new tweeters easy.
These were perfect and made the tweeter instal extremely easy.
Not sure what'll fit? Just call.
Tell us your vehicle and the tweeters you're running - we'll confirm the right size before you order.



