2014-2019 Lexus IS & RC 6.5-inch Front Speaker Adapters | 1.5-inch CNC HDPE
Two-piece 1.5-inch HDPE construction with pass-through wire routing for Lexus IS and RC
SKU: Lexus65SpeakerAdapters
Built for the factory location.
The Lexus IS and RC use a deep, complex front speaker cavity that requires a purpose-built adapter. This two-piece CNC-machined HDPE solution delivers 1.5 inches of precision-fit mounting depth with a pass-through wire hole for clean installation.
Check before you buy
Converts factory 8-inch Lexus speaker location to standard 6.5-inch round. Compatible with Focal, Hertz, Audison, JBL, Kicker, Morel, and more. All brand names are trademarks of their respective owners and are used for compatibility reference only. Not sure which system you have? Ask us before you buy.
Full specifications
- Speaker Size
- 6.5-inch
- Factory Size
- 8-inch
- Material Thickness
- 1.5-inch HDPE
- Construction
- Two-piece
- Cutout Diameter
- 143.7 mm
- Wire Routing
- Pass-through
- Mounting Location
- Front doors
- Sold As
- One pair
The rest of the route, in one cart.
One part from each DIY step that fits your vehicle. Open any of them to choose its options and add it to your cart without leaving this page.
20 ft of power + 20 ft of ground in 100% OFC Kicker wire, fused at the battery — 1/0, 4 or 8 gauge.
Lexus owners installing aftermarket tweeters or mid-range drivers from component speaker kits
Not all speaker adapters are built the same.
A speaker adapter lives in your doors and panels through heat, cold, moisture, and constant road vibration - with your new speakers bolted straight to it. Most competitors reach for metal, ABS, expanded PVC, or expanded HDPE; wood is the common DIY shortcut. Here's how each actually behaves where it counts.
| Material | Easy to work with | Holds real weight | Low material cost | Shrugs off moisture |
|---|---|---|---|---|
material sample
What SGS uses
Solid Core USA-Made HDPE
Dense, Non-Porous and Forgiving
| Strong | Strong | High cost | Strong |
material sample
Competitor materialMetal
Heavy, resonates, hard to cut
| Fails | Strong | High cost | Strong |
material sample
Competitor materialExpanded HDPE
Hollow core, weak at bolt holes
| Strong | Fails | Low cost | Fails |
material sample
Competitor materialABS
Rigid but thin and brittle
| Strong | Fails | Low cost | Fails |
material sample
Competitor materialExpanded PVC
Often foamed, brittle when cold
| Strong | Fails | Low cost | Fails |
material sample
DIY build shortcutWood / Plywood
Absorbs moisture, swells, rots
| Strong | Strong | Low cost | Fails |
Built in-house, start to finish.
Every adapter is designed, machined, and finished under one roof in Mount Juliet, Tennessee. No outsourcing, no imported blanks - just USA-made HDPE, a CNC machine, and people who care whether it fits right. Here's how a flat sheet becomes a set of adapters cut for your vehicle.
Video - From the shop floor
Solid Core USA-Made HDPE
It starts with a sheet of 100% USA-made HDPE - solid all the way through, the same material trusted in marine and industrial builds. No hollow cores.
Precision CNC Machining
Each set of adapters is nested from our own CAD files and cut on our CNC machine. Feeds and speeds are dialed in for HDPE so every speaker cutout comes off clean and every factory mounting hole lands exactly where it should.
Hand-Finished & Inspected
Every adapter is deburred and inspected by hand before it's packed. If it wouldn't go in our own truck, it doesn't ship.
Packed to Survive Shipping
Every set is wrapped, boxed, and packed by the same hands that made it - with the gasket tape and mounting screws bagged, so nothing arrives loose, scratched, or missing.
Everything customers actually ask.
The questions we get most on speaker adapters - answered straight. Not sure if yours is here? Call, and a human answers.
One year, on everything we sell. Every item is covered for one year from delivery. If something fails in that first year, we make it right. Questions about a claim? Call us — a real person handles it with you.
Asked by truck owners
2 answered by our teamYes, we sell them to fit the Focal drivers, just add them to your cart and checkout. It's a traditional size where as the Kicker KS are smaller.
Answered by the SGS team · Feb 2023
Most speakers are going to fit, just always try to stay under 3-inch which should cover 99% of car stereo speakers.
Answered by the SGS team · Oct 2022
Bolt the adapters in. No drilling.
Every set ships ready to install at home. Follow the steps for your vehicle - the adapters go in with basic hand tools, no drilling.
-
Remove front door panel trim and fasteners
-
Carefully disconnect door handle and window switch connectors
-
Remove door panel from clips
-
Disconnect factory speaker wiring
-
Unbolt and remove factory 8-inch speaker
-
Place two-piece HDPE adapter into factory speaker cavity
-
Route speaker wire through pass-through hole
-
Secure adapter with mounting hardware (some factory hardware reused)
-
Mount 6.5-inch aftermarket speaker to adapter
-
Reinstall door panel and reconnect switches
How they hold up once they're installed.
These are not advertised for 21- IS but I took a chance with these brackets and they fit flawlessly. I do recommend using a thicker foam tape than what’s provided with the kit to seal it to the door because the screw mounts do not sit flat on the door skin. There was a gap between the skin and adapter so I used thicker foam tape and sealed it up with sound deadener. Sundown Audio SA-65CS, 6.5” driver fits with room to spare inside the door for window. Used NVX silicone baffles to seal to the panel.
Took me months of research to find someone who makes an adapter that fits my Lexus UX. On a whim I ordered these and they fit the FRONT doors perfectly. Highly recommend these.
They fit perfect and work just for my project very happy with the workmanship and quality exact fit.
Communication and craftsmanship is A+. Works perfectly with http://metraonline.com/part/IBSBF65 the baffle sits flush against the door panel. If you need specific sizes cut for different brand speakers just give them an email/call and they'll work it out for you. Depending on the mid used may need to trim the dash grill, speaker sat a little high. But once trimmed it was perfect.
Researching the needed exact information for replacement speakers for Mark Levinson equipped 2017 Lexus IS 350 F sport AWD was a somewhat tough job. Front speakers are 3.5" ML coaxial crap and most suppliers note 4" speakers as replacements. I opted for coaxial Hertz CX100 for the left and right fronts and Hertz DCX100.3 for the center-channel front. Brackets must be removed as the Lexus has 2 bracket mounts and Hertz has 4 mounting brackets. Modifying the plastic dash lip towards the windshield is required on left and right locations to allow these speakers to sit flat. I single smaller high-end tweeter could be used in these locations with SGS adapters but you would lose a good deal of mid-range. The front doors have 7.1" dia. 5.3 Ohm Mark Levinson which is near impossible to match exactly with anything quality. The SGS 6.5" adapters work perfectly with my chosen Focal's. You can also separate the adapter and run the speaker wire adapter cables through a small slot that SGS provided. Plan for multiple hrs. to attach sound-deadening material properly. The rear doors can easily be handled by a readily available adapter for 6.5" speakers. I chose Focal PC 165 FE Flax EVO 6.5s for both the front and rear doors.
Now I wish SGS made an adapter to use a shallow 8" sub to replace the ML crap sub. No one lists a sub replacement for the 7.8" 6-ohm sub and the easiest way to replace it would be to carefully strip the plastic raised bracket from the existing sub to use it to mount an 8" shallow quality sub-replacement. I am dreading starting the sub-replacement project. Thank you SGS for the front door adapters!!!!
This review updates the number of stars to 5 as there was a problem seeing the stars on the review site in my original review.
Researching the needed exact information for the replacement of speakers for Mark Levenson equipped 2017 Lexus IS 350 F sport AWD was a somewhat tough job. Front speakers are 3.5" ML coaxial crap and most suppliers note 4" speakers as replacements. I opted for coaxial Hertz CX100 for the left and right fronts and Hertz DCX100.3 for the center-channel front. Brackets must be removed as the Lexus is 2 bracket mount. Modifying the plastic dash lip towards the windshield is required on left and right locations to allow these speakers to sit flat. I single smaller tweeter could be used in these locations with SGS adapters but you would lose a good deal of mid-range. The front doors have 7.1" dia. 5.3 Ohm which is near impossible to match with anything quality. The SGS 6.5" adapters work perfectly with my chosen Focal's. You can also separate the adapter and run the speaker wire adapters through a small slot that SGS provided. Plan for multiple hrs to attach sound-deadening material properly. The rear doors can easily be handled by readily available;e adapter for 6.5" speakers. I chose Focal PC 165 FE Flax EVO 6.5's for both the front and rear doors.
Now I wish SGS made an adapter to use a shallow 8" sub to replace the ML crap sub. No one lists a sub replacement for the 7.8" 6-ohm sub and the easiest way to replace would be to strip the plastic raised brace from the existing sub carefully to use a mount 8" quality sub-replacement. I am dreading starting the sub-replacement project. Thank you SGS for the front door adapters!!!!
I'm sorry but these aint worth $130. Also kind of a PITA to drill into, I just gave up and used long screws to keep the speaker in between the bracket.
Perfect fit and great quality
Very high build quality! Perfect fitment. Took a little while to receive, but was not in a rush. Highly recommend these adapters as Lexus models tend to vary and these work perfectly. They even customized the tweeter adapter to accommodate my Focal's.
I was very pleased to find out that SGS actually custom made these mounts to fit the speakers I had purchased. They messaged me after the purchase to ask what speakers I was using, made mounts that fit the speakers perfectly. After I realized my audio upgrade was more work than I wanted to tackle I took it to a local Audio install shop and when I picked up my vehicle I asked how the adapters worked out.. even they said they were perfect! SGS was the only place I could find adapters that I knew were going to work for my Lexus, even though they may have been a little more pricey than another option that may or may not have fit, the service and quality were what came through on this one. I’ve heard the saying in the past, buy once, cry once, which with the quality and service that come with the product purchace here, no need to cry. Hats off to the people at SGS!!! Thanks!
Hi there!
I previously bought a pair of these for my Kicker KS speakers, I am upgrading to focals but they do not fit the custom ring that you guys made for the kickers. I am putting in Focal 165AS components. I see someone in the reviews also had these. Any way I can get them made for my focals?
Yes, we sell them to fit the Focal drivers, just add them to your cart and checkout. It's a traditional size where as the Kicker KS are smaller.
Good morning, I am looking to buy the 8 inch adapter for my front door 2016 Lexus is200t and I was wondering with the adapter installed what kind of dept would I have for a 6.5 speaker? Would I have to use a slim speaker or most speaker would fit? Thank you.
Most speakers are going to fit, just always try to stay under 3-inch which should cover 99% of car stereo speakers.
Not sure what'll fit? Just call.
Tell us your vehicle and the speakers you're running - we'll confirm the right adapters before you order.


material sample
material sample
material sample
material sample
material sample