Loaded Amp RackFrom $1,840
Choose options · $1,840
Loaded Kicker CXA1200.1 amp rack with Kicker KEYLOC, two fused distribution blocks and relay, shown with its plug-in harness, Kicker bass knob, cable glands, braided power and ground wires and install tools, for 2024+ F-150 and 2023+ Super Duty

Kicker Loaded Subwoofer 1200wrms Amplifier Rack for Ford 2023+ Super Duty and 2024+ F-150 Trucks

5.0 · 22 reviews
1,200 W RMS @ 2 ohmsPre-tuned in-houseFixes B&O bass roll-offPlug-in harnessHandcrafted in TN

Kicker CXA1200.1 pre-wired and pre-tuned on our HDPE rack. Plugs into your factory audio; you add the subwoofer.

From $1,840
Shipping calculated at checkout
Choose your options Required
Choose your options
Your selection includes
  • Kicker CXA1200.1 mono amplifier, mounted and wired on the rack
  • Ten87 Design driver-side amp rack, 1/2-inch solid-core USA-made HDPE
  • Kicker KEYLOC line output converter, pre-tuned and wired on the rack
  • Fused distribution blocks and relay, on the rack
  • Plug-in T-harness for the factory B&O amplifier (B&O trucks)
  • Subwoofer block-off plate and screws (B&O trucks)
  • Dash plug, extension harness and junction (trucks without B&O)
  • Kicker remote bass knob
  • 4-gauge OFC copper power and ground wire
  • Inline fuse for the power wire
  • 2 watertight cable glands for the floor holes
  • Subwoofer lead with quick-disconnect plug
  • LED-light lead with quick-disconnect plug
  • 2 aluminum floor feet, M8 bolts and spacers
  • Pry bar, flush cutters and bass-knob template
  • Cable ties and tie mounts
Top questions 8 answered
See all 8 questions
Questions? Text us at 615-610-1413
Fits your vehicle In-house support
The rack · Performance tier

How it performs. In your truck.

Our score for this rack, and how it rates on the four things we judge every amplifier rack on.

Tier
Performance
Amplifier power
1200 W RMS
Where it lands in our lineup
  1. Essential
  2. Performance
  3. Audiophile
  4. Flagship

Four things we rate

Hover or tap a measure
Loaded subwoofer amplifier rack

The details.

This rack is the amplifier half of a subwoofer upgrade for trucks with B&O or base factory audio. A Kicker CXA1200.1 and a Kicker KEYLOC come mounted, wired and pre-tuned on our half-inch HDPE rack, which bolts in behind the driver-side rear seat and plugs into the factory audio with a harness, so no factory wires are cut. You add the subwoofer: 1,200 watts RMS into 2 ohms or 1 ohm, 600 into 4 (Kicker's ratings).

Check before you buy

Choose your factory audio above: B&O trucks get a T-harness and a block-off plate, trucks without B&O a dash harness. Power and ground need two 3/4-inch holes in the floor. Not sure which audio you have? Call or text 615-610-1413.

Full specifications

Amplifier System
CXA1200.1
RMS Power Output
1,200 W RMS
4-Ohm Output
600 W RMS
Integration
Kicker KEYLOC
Pre-Tuned Signal
Yes
Power Wire
4 AWG OFC
Mounting Location
Driver side
Factory Audio
B&O or base
Loaded racks for your vehicle

Compare loaded subwoofer racks.

Common questions

Everything customers actually ask.

The questions we get most on loaded amplifier racks - answered straight. Not sure if yours is here? Call, and a human answers.

Don't see your question?
A human answers - no bots, no queues.
615-610-1413
Install it yourself

Step by step for your vehicle.

Where install steps exist for your exact part, they're below - with the tools you'll need.

DifficultyModerateTime~4 hrDrilling2 holes drilledTools7 tools
Tools you'll need
10 mm socket
13 mm socket
3/4-inch step bit and drill
1/8-inch drill bit
Utility knife
Pry bar (included)
Flush cutters (included)
Written steps
  1. Fold down the rear seat backs; the seats do not need to come out.

  2. On B&O trucks, take the factory subwoofer out from behind the driver-side seat.

  3. Find the floor threads for the feet (they can be under the carpet and a square of tape), screw the feet into the slots for your truck from the mounting feet chart, and bolt the rack down with a spacer under each foot.

  4. Bolt the top bracket to the seat-latch bracket, in front of it.

  5. On B&O trucks, pre-drill 1/8-inch holes and screw the block-off plate over the factory subwoofer opening, cork side toward the hole.

  6. On B&O trucks, find the factory amplifier behind the carpet panel on the back wall toward the passenger side, unplug the one connector the T-harness matches, plug the T-harness in between, and leave the amplifier's other plugs connected.

  7. On trucks without B&O, plug the dash harness in at the radio and run the extension harness back to the rack along the driver side.

  8. Run power and ground from the battery down to the frame rail, back along it, and into the cab through two 3/4-inch floor holes sealed with the included glands.

  9. Connect the ground at the battery, on the battery side of the factory battery sensor, and the power wire with its inline fuse.

  10. Connect power and ground to the distribution blocks on the rack, plug in the subwoofer lead, and plug in the LED-light lead if your enclosure has lights.

  11. Run the Kicker bass knob cable forward if you want the knob within reach, test the system, then fold the seat backs up.

Owner reviews - real installs

How they hold up once they're installed.

Write a review
5.0/ 5
22 reviews
Questions? Talk to us

Not sure what'll fit? Just call.

Tell us your vehicle and factory system - we'll confirm the right loaded rack before you order.

Don
Senior build specialist
Talk to Don
Call or text
615-610-1413

No bots, no phone tree - a real builder picks up.

Shipping calculated at checkout Financing available Authorized online retailer In-house tech support
From $1,840Loaded Subwoofer Amp Rack
Choose options