Loaded Amp RackFrom $2,200
Choose options · $2,200
Kicker amp rack for Ford F-Series with Sony factory amplifier, add-a-subwoofer interface box, wiring and tools

Kicker Loaded Subwoofer 1800wrms Amplifier Rack for Ford F-Series Vehicles (All Factory Systems including B&O Unleashed)

5.0 · 22 reviews
1,800 W RMS @ 2 ohmsPre-tuned in-houseFixes B&O bass roll-offPlug-in harness

Kicker CXA1800.1 pre-wired and pre-tuned on our HDPE rack. Plugs into your factory audio; you add the subwoofer.

From $2,200
Shipping calculated at checkout
Choose your options Required
Choose your options
Your selection includes
  • Kicker CXA1800.1 mono-block amplifier, mounted and wired on the rack
  • Driver-side amp rack, 1/2-inch HDPE, with its top bracket
  • Two distribution blocks, an automotive relay and the Ford sub amp rack harness
  • Subwoofer wire with a quick-disconnect plug
  • Kicker bass knob and a mounting template
  • 4-gauge OFC power and ground kit with an inline fuse holder, 150 A fuse and two cable glands
  • 2 metal rack brackets, 2 M8 floor bolts, 2 spacers and 8 screws in a hardware tin
  • Pry bar, flush cutters and cable ties
  • B&O options: T-harness and a pre-tuned Kicker KEYLOC
  • Oval-subwoofer B&O options: subwoofer block-off plate, screws and cork gasket
  • Sony option: PAC AmpPRO SUB interface and Kicker 5-meter RCA cables
  • Options without a factory amplifier: Kicker KEYLOC, radio plug, 14-foot extension harness and subwoofer junction
Top questions 8 answered
See all 8 questions
Questions? Text us at 615-610-1413
Fits your vehicle In-house support
The rack · Performance tier

How it performs. In your truck.

Our score for this rack, and how it rates on the four things we judge every amplifier rack on.

Tier
Performance
Amplifier power
1800 W RMS
Where it lands in our lineup
  1. Essential
  2. Performance
  3. Audiophile
  4. Flagship

Four things we rate

Hover or tap a measure
Loaded subwoofer amplifier rack

The details.

This rack is the amplifier half of a subwoofer upgrade for trucks with B&O, Sony or base factory audio. A Kicker CXA1800.1 comes mounted, wired and pre-tuned on our half-inch HDPE rack, which bolts in behind the driver-side rear seat, and it plugs into the factory audio with the interface made for your system, so no factory wires are cut. You add the subwoofer: 1,800 watts RMS into 2 ohms or 1 ohm, 900 into 4 (Kicker's ratings).

Full specifications

Amplifier System
CXA1800.1
RMS Power Output
1,800 W RMS
4-Ohm Output
900 W RMS
Integration
KEYLOC or PAC
Pre-Tuned Signal
Yes
Power Wire
4 AWG OFC
Mounting Location
Driver side
Factory Audio
B&O/Sony/base
Loaded racks for your vehicle

Compare loaded subwoofer racks.

Common questions

Everything customers actually ask.

The questions we get most on loaded amplifier racks - answered straight. Not sure if yours is here? Call, and a human answers.

Don't see your question?
A human answers - no bots, no queues.
615-610-1413
Install it yourself

Step by step for your vehicle.

Where install steps exist for your exact part, they're below - with the tools you'll need.

DifficultyModerateTime~4 hrTools8 tools
Tools you'll need
10 mm deep-well socket
10 mm socket
13 mm socket
3/4-inch step bit and drill
1/8-inch drill bit
Utility knife
Pry bar (included)
Flush cutters (included)
Written steps
  1. Fold down the rear seat backs; the seats do not need to come out.

  2. If a factory subwoofer is behind the driver-side seat, take it out with the studs it sits on (10 mm deep-well socket); if the factory amp sits on a bracket there, take the bracket out and mount the amp on the rack.

  3. Find the floor threads for the feet (they can be under the carpet and a square of tape), screw the feet into the slots for your truck from the mounting feet chart, and bolt the rack down with a spacer under each foot.

  4. Bolt the top bracket to the seat-latch bracket, in front of it.

  5. On oval-subwoofer B&O trucks, pre-drill 1/8-inch holes and screw the block-off plate over the factory subwoofer opening, cork side toward the hole.

  6. On B&O trucks, plug the T-harness in between the factory amplifier and the one connector it matches, and leave the amplifier's other plugs connected.

  7. On Sony trucks, plug the included PAC interface into the factory wiring with its vehicle-specific harness; no factory wires are cut.

  8. On trucks without a factory amplifier, plug the dash harness in at the radio and run the extension harness back to the rack along the driver side.

  9. Run power and ground from the battery down to the frame rail, back along it, and into the cab through two 3/4-inch floor holes sealed with the included glands.

  10. Connect the ground at the battery, on the battery side of the factory battery sensor, and the power wire with its inline fuse.

  11. Connect power and ground to the distribution blocks on the rack, plug in the subwoofer lead, and plug in the LED-light lead if your enclosure has lights.

  12. Run the Kicker bass knob cable forward if you want the knob within reach, test the system, then fold the seat backs up.

Owner reviews - real installs

How they hold up once they're installed.

Write a review
5.0/ 5
22 reviews
Questions? Talk to us

Not sure what'll fit? Just call.

Tell us your vehicle and factory system - we'll confirm the right loaded rack before you order.

Don
Senior build specialist
Talk to Don
Call or text
615-610-1413

No bots, no phone tree - a real builder picks up.

Shipping calculated at checkout Financing available Authorized online retailer In-house tech support
From $2,200Loaded Subwoofer Amp Rack
Choose options