Ford F-150 & Super Duty Door Speaker Adapters – 8", 6x9" or 6.5" Front, 6.5" Rear (2015-2026 F-150, 2017-2026 Super Duty)
Bolt an 8", 6x9" or 6.5" speaker into the front doors and a 6.5" into the rears — no drilling.
SKU: F-Series-Front8-Rear65-CompleteKit
Built for the factory location.
The factory speaker comes out with a 7 mm socket. Our adapter goes in on the same screw locations — four in the front doors, three in the rears — and gives an 8-inch, 6x9-inch or 6.5-inch speaker a flat 1/2-inch base of solid-core, USA-made HDPE to mount to.
Every set is a left and right pair: the wire pass-through on each adapter faces its own side. A foam gasket goes around the speaker on the adapter.
The Complete Kit adds plug-in Ford speaker harnesses, so you never cut a factory wire — keep the factory speakers and screws and the truck goes back to stock.
Check before you buy
Front doors give about 3-1/4 in of mounting depth; a deep 6x9 magnet can touch the window parts. Rear doors take 6.5-inch only. Not sure? Call us with your speaker model.
Full specifications
- Available Sizes
- 8, 6.5 or 6x9
- Rear Size
- 6.5-inch
- Mounting Depth
- 3.25 in front
- Mounting Method
- Factory holes
- Wire Routing
- Pass-through
- Plug Harness
- Complete Kit
- Sold As
- Pairs (L + R)
- Reversible
- Back to stock
The rest of the route, in one cart.
One part from each DIY step that fits your vehicle. Open any of them to choose its options and add it to your cart without leaving this page.
Mounting amplifiers, a processor and distribution behind the driver-side rear seat: it bolts to three factory points, with no drilling.
Owners who need one compact amp or a DSP on the driver side without taking up the whole area behind the rear seat.
Owners running a 5-channel amp or micro amplifiers who want a clean, secure mount behind the rear seat.
Mounting a compact amplifier or processor behind the passenger-side rear seat, with no drilling and the factory subwoofer left in place.
2015-2026 Ford F-150 and Super Duty SuperCrew owners who want a hidden, clean amp install in the underseat storage area. Not for trucks with Pro Power Onboard.
For owners who need the whole back wall: 53.8 inches for several amplifiers, with room behind for distribution blocks, relays or a DSP.
20 ft of power + 20 ft of ground in 100% OFC Kicker wire, fused at the battery — 1/0, 4 or 8 gauge.
Add a sub amp to Ford B&O — fix the bass roll-off with a pre-set KEYLOC, or keep it and save.
A pair of factory 2-pin plug pigtails with bare OFC copper leads. Plug-and-crimp aftermarket speaker install with zero factory wire cuts.
Takes the place of the rear B&O amp and hands your amplifiers six clean analog channels.
Plug-in T-harness for 2021+ Ford non-amplified factory stereos. Hand-built in Nashville with OFC copper, soldered 4-channel Straight Wire RCA tips, and fully reversible installation.
Plug-in T-harness for 2015-2020 Ford F-Series and other pre-2021 non-amplified Fords. Hand-built in Nashville with OFC copper, soldered 4-channel Straight Wire RCA tips, and fully reversible installation.
SGS-built plug-in harness that connects a Kicker KEYLOC module to your Ford B&O factory amp output. Pick the variant that matches your factory subwoofer shape — YMM will auto-select if your vehicle is in our database.
A pair of OFC copper pigtails with Ford's small BLACK tweeter / mid-range factory connector. Check your own plug color before ordering — black = this product, gray = different SKU.
Plug-in dash-side harness that gives you access to the speaker wires running to the factory rear-door speakers on 2021-2023 F-150 B&O Unleashed trucks. Connect your amp output at the dash instead of splicing door wires.
Zero-splice install harness — clean, reversible wiring with no cut factory connectors.
2025+ Ford A²B stereo interface — now works on all Broncos (including non-B&O). Burr-Brown DAC up to 192 kHz. Same engine as the ZEN-A2B Plus.
F-150 and Super Duty owners installing aftermarket tweeters from a 2-way or 3-way component speaker kit
2021+ Ford truck owners with the non-amplified audio system installing aftermarket tweeters
2021+ Ford F-150, Lightning, and Super Duty owners with B&O audio upgrading factory midrange speakers
Closing the factory access holes behind your door speakers
Closing the factory access holes behind your door speakers
Trucks with B&O audio - required when removing the factory subwoofer
2009-2014 F-150 SuperCrew and SuperCab front door speaker upgrades
2015-2020 F-150 SuperCab and 2017-2022 Super Duty SuperCab door speaker upgrades
2018-2023 Ford Expedition and Expedition Max door speaker upgrades - all trims and audio packages
Two Ten87 Design 6.5-inch subs in a ported box that hides behind the rear seat, with the compact amp rack that fits beside it. Bring your own amp.
Kicker's own carpeted truck box with two 10-inch L7T subs installed, made to sit under the rear seat.
Two 6.5-inch subs in a ported box behind the rear seat — for your own amp, and the seat still folds up.
Genuine JL Audio Stealthbox: two 12-inch TW3 subs in a sealed box that bolts in under the rear seat.
Two Ten87 Design 6.5-inch subs in a ported box that hides behind the rear seat. Bring your own amp.
Custom-fit subwoofer enclosure for the Ford F-Series (2009–2026) — tight, hidden bass built around your Arc Audio.
Not all speaker adapters are built the same.
A speaker adapter lives in your doors and panels through heat, cold, moisture, and constant road vibration - with your new speakers bolted straight to it. Most competitors reach for metal, ABS, expanded PVC, or expanded HDPE; wood is the common DIY shortcut. Here's how each actually behaves where it counts.
| Material | Easy to work with | Holds real weight | Low material cost | Shrugs off moisture |
|---|---|---|---|---|
material sample
What SGS uses
Solid Core USA-Made HDPE
Dense, Non-Porous and Forgiving
| Strong | Strong | High cost | Strong |
material sample
Competitor materialMetal
Heavy, resonates, hard to cut
| Fails | Strong | High cost | Strong |
material sample
Competitor materialExpanded HDPE
Hollow core, weak at bolt holes
| Strong | Fails | Low cost | Fails |
material sample
Competitor materialABS
Rigid but thin and brittle
| Strong | Fails | Low cost | Fails |
material sample
Competitor materialExpanded PVC
Often foamed, brittle when cold
| Strong | Fails | Low cost | Fails |
material sample
DIY build shortcutWood / Plywood
Absorbs moisture, swells, rots
| Strong | Strong | Low cost | Fails |
Built in-house, start to finish.
Every adapter is designed, machined, and finished under one roof in Mount Juliet, Tennessee. No outsourcing, no imported blanks - just USA-made HDPE, a CNC machine, and people who care whether it fits right. Here's how a flat sheet becomes a set of adapters cut for your vehicle.
Video - From the shop floor
Solid Core USA-Made HDPE
It starts with a sheet of 100% USA-made HDPE - solid all the way through, the same material trusted in marine and industrial builds. No hollow cores.
Precision CNC Machining
Each set of adapters is nested from our own CAD files and cut on our CNC machine. Feeds and speeds are dialed in for HDPE so every speaker cutout comes off clean and every factory mounting hole lands exactly where it should.
Hand-Finished & Inspected
Every adapter is deburred and inspected by hand before it's packed. If it wouldn't go in our own truck, it doesn't ship.
Packed to Survive Shipping
Every set is wrapped, boxed, and packed by the same hands that made it - with the gasket tape and mounting screws bagged, so nothing arrives loose, scratched, or missing.
Everything customers actually ask.
The questions we get most on speaker adapters - answered straight. Not sure if yours is here? Call, and a human answers.
One year, on everything we sell. Every item is covered for one year from delivery. If something fails in that first year, we make it right. Questions about a claim? Call us — a real person handles it with you.
Asked by truck owners
3 answered by our teamNot at the current time, just not a huge demand for this size in this truck
Answered by the SGS team · Jul 2023
Yes, all of the Focal drivers fit front + rear in these trucks
Answered by the SGS team · Mar 2023
The ID cutout is 185.928mm, so they should fit great.
Answered by the SGS team · May 2022
Bolt the adapters in. No drilling.
Every set ships ready to install at home. Follow the steps for your vehicle - the adapters go in with basic hand tools, no drilling.
-
Remove door panel trim and fasteners
-
Disconnect factory speaker wiring harness
-
Unbolt and remove factory speaker
-
Place HDPE adapter over factory mounting holes
-
Secure adapter with included hardware
-
Connect speaker wire harness (Complete Kit) or solder/crimp connections
-
Mount aftermarket speaker to adapter with included screws
-
Apply gasket tape for airtight seal
-
Reinstall door panel and test
How they hold up once they're installed.
Very high quality speaker adapters! My focal 6KMs fit like a glove and they even added the little touches like a pre-drilled hole for the factory speaker wires and foam surround to put on the speaker to ensure a good seal.
Top notch company with top notch products!
I purchased these kick-panel speaker adapters for my 2022 Ford Bronco to install JL Audio C3-650 speakers. The adapters are very well-made, with excellent fit and construction.
I made a small modification to the wire pass-through opening to accommodate my preferred wiring arrangement, using short pigtails with connectors rather than soldering directly to the speakers. Everything came together nicely, and I’m very pleased with the finished installation.
Sounds Good Stereo was also responsive when I reached out with a question about the installation. Overall, a quality product and a good experience. I would definitely recommend them
Son mi primera opción cuando le hago modificaciones a mi guagua y con una llamada tambien orientan
Makes big difference in sound. Added additional sound deadening inside the door and on panels. Paired with 6x9 JL C1 speakers in front doors and 6x5 JL C1 component speakers in rear doors. With my JL steathbox subwoofer turned off, these put out better bass than the factory speakers ever did using the stock B/O amp. Clarity is improved. Installing NavTv DSP processor and JL RD900/5 channel amp soon to replace the B/O amp. Giving 4 stars due to having to shave the speaker plates to fit the 6x9’s in the front plates.
As expected, great product at a reasonable value. I did have to open the internal circumference to fit my Karma 6x9. I have to shave off about 1/8" all the way around, however they are a more robust 6x9. Im sure the fit would be flawless on a standard 6x9.
Used these adapters to mount my Morel Hybrid 6 1/2 front woofer and rear Hybrid Integra in rear. Worked out well, although did have to drill bigger hole to accomadate for 16ga speaker wire ( two hole for rear since using mounted passive crossover near speaker with Integra's ). Make sure to mount as equal as possible. Overall even though my statements may sound somewhat negative the adapters are nice. Don't think all of adapters out there are perfect and to the T. Do like them and recommend them.
Again as with everything you use put attention to how to position and use properly. Do Recommend Overall. Solid mounts and fit perfectly
First I want to say I love everything about car audio and to have companies like Sounds Good that are also passionate about it, with great customer service, is great for our community! I haven’t pulled the trigger on a big item from them yet but I know by the quality and precision they put into the speaker adapters is amazing and you truly get what you pay for. You may think it’s silly and it’s just a speaker adapter but I promise you it’s not, all the “normal” adapters I’ve used for years not having a clue this was even an option are junk in comparison. I’m sure my door panel would bend or possibly break before this adapter does. With all that said, I’m happy and I recommend this product 🤣
Side note I purchased this in the 8” and 6.5” the 8’s are for the future
These are not your basic speaker adapters. The quality of the product and packaging is way above anything you will find elsewhere. If you care about your install quality this is definitely what you want. The service is also top notch! Excellent communication about shipping and free goodie’s included with order. No doubt the best adapters and block off plates you can buy!
These are probably workable, but the mounting area is more like 3-7/16" - so a speaker with an actual 3-1/2" diameter will not fit without some modification. The inner diameter farther down is also a little snug, so getting wires on the speaker terminals will require some modifications to that as well.
Overall, not bad and the quality of the plastic is good. They just aren't a drop-in upgrade.
I got just the adapter plates for front 6x9 to 6.5 and the rear 6.5. Quality adapter plates. Good and thick. Solid mounting surface for the new speakers. Not like the cheaper ABS plastic adapters. One draw back for my installation (2016 Ford Explorer XLT) was that the pre drilled holes did not line up at all with the holes actually used by the factory speaker. While not a problem for myself but might be for others that are not good at fabrication (I.e. drilling new holes). In the end, the plates fit well with new holes drilled and better sound was achieved with better speakers.
The quality is outstanding and make all other products feel like garbage. It’s pricey but definitely durable without a doubt.
Can’t speak for all 6.5” speakers, but my Focal KX2 mid bass drivers and Flax Evo coaxials fit like a glove. Absolute necessity when upgrading speakers.
In my previous Ford truck I used Metra products for 6.5' speakers. They were "universal" and trash. It wasn't worth the trouble of return so I trashed them and spent way too much time build wood speaker adaptors. These adaptors took out all the guesswork and were paired with high quality CDT audio components and coaxials. Perfect fit.
First and foremost one of the better customer experiences I've had. Within minutes of ordering I received a tracking number. Package arrived within a few days packed well and everything included was of high quality. My suggestion for product improvement is that the speaker adaptors are cut for a particular diameter speaker, so it is likely to be a "sloppy" fit for many speakers they dont offer. Most of us D.I.Y type could cut our own hole to fit our exact speaker. Either offering customers the ability to customize adapters before shipping or offer a uncut adapter for us to modify once received.
I was just about to to try some metal eBay baffles that may or may not fit. These HDPE baffles are a direct fit, and almost a dense. I replaced some birch ones that cost more than these, you can see how they held up (or didn't) to a relatively sealed door.
After installation the midbass doubled and the midrange went right back to the middle of the dash. Will ALWAYS buy this brand from here forth!!
Using JL Audio 5x7 components in front, can you accommodate (make) the front adapter for the 5x7?
Not at the current time, just not a huge demand for this size in this truck
I need an adapter plate for 3.5 inch speaker focal brand to replace factory speaker in 2019 ford mustang with B&O system can you make them or do you have them already and if so how much ?
Here you go. Make sure in the notes section in the shopping cart you add the Focal part number so we can verify fitment before it ships
https://soundsgoodstereo.com/products/2015-2020-ford-mustang-custom-mid-range-adapter-for-aftermarket-mid-range-speakers
Not sure what'll fit? Just call.
Tell us your vehicle and the speakers you're running - we'll confirm the right adapters before you order.
































material sample
material sample
material sample
material sample
material sample