Arc Audio Class A/B SE 2150 600w 2ch SQ Audiophile Amplifier
Arc Audio Class A/B SE 2150 600w 2ch SQ Audiophile Amplifier
May 30, 2013
Arc Audio Class A/B SE 4100 4ch SQ Audiophile Amplifier
Arc Audio Class A/B SE 4100 4ch SQ Audiophile Amplifier
May 30, 2013
Show all

Arc Audio Class A/B SE 2300 1300w 2ch SQ Audiophile Amplifier

$1,449.00

2 Channels @ 4 ohms 330 Watts
2 Channels @ 2 ohms 660 Watts
1 Channel @ 4 ohms (bridged) 1300 Watts
1 Channel @ 2 ohms (bridged) 1300 Watts
Frequency Response 4Hz – 100kHz
Crossover Range 30Hz – 500Hz
Crossover Range X10 300Hz – 5500kHz
Bass Boost 0 – 15dB @ 20Hz – 80Hz
S/N Ratio 90 dB (RCA In)
Input Sensitivity (Low) .3V – 4V
Input Sensitivity (Bal) .4V – 8V
Max current draw 222A @ 1800 Watts 20% THD
Idle Current 1.14 Amp
Fuse 3 x 40 Amp
Dimensions 19.5″(L) x 8.0″ (W) x 2.5″(H)

Signature Edition by Robert Zeff is our no compromise, high power, audiophile amplifier designed and engineered by Robert Zeff and the staff at Nikola Engineering. This design is taken from Roberts many years of experience in both professional and the car audio industries where he daily used, repaired and built high power, high fidelity amplifiers. With these lessons well learned over 30 years he finally had the opportunity to make for ARC Audio the no compromise, no limits amplifier he had always dreamt of.

Signature Edition is a Hard Bias Class A/B amplifier. A simple Class B amplifier uses 2 output transistors to supply the current that moves the speaker. The positive transistor will push the woofer out and the negative will pull it back. In this design only 1 transistor is working at any give time. It is the transition between positive and negative that leads to the higher distortion that makes a Class B amplifier unacceptable for audio reproduction. In most cases a bias circuit is added to a Class B amplifier making it a Class A/B. The Bias circuit improves the distortion by slightly turning on the unused output device while current is flowing across the other. The more bias you add the lower the distortion but there is a side effect. Heat is created as the 2 output transistors are both on at the same time. The more bias you add the better it sounds but the more heat you produce but heat changes the natural bias of the output devices.

More heat equals more bias until you reach the point of over bias and the amplifier fails. The trick to the Signature Edition Bias circuit is managing the bias current at any temperature. By carefully matching the bias of every amp we are able to maintain stable bias across the temperature range allowing the technician “dial in” much more bias then a conventional class A/B amplifier. This is one of the key elements to the Signature Editions amazingly transparent sound.

The key to running so much bias is heat management. Signature Edition has a unique heat sink design that uses a 4″ fan mounted in the center of the circuit board to force cool air in a cross flow pattern across a massive finned heat sink before exhausting it from the ends. This design minimizes the effects of installation location on the thermal performance of the amplifier. Mounted upside down, under or behind a seat or beneath a panel Signature Edition will perform equally well.

To further improve the dynamics and efficiency the Signature Edition amplifier exclusively use stiffly regulated, fully isolated power supplies. Regulation not only improves the damping factor and overall control of an amplifier but it eliminates any affect of voltage drops in the charging system may have.

Audiophile sound quality based design
Designed by Robert Zeff
Class A/B switching design
Microprocessor controlled design
Microprocessor controlled Code based flashing diagnostics
Concealed adjustment controls
Open architecture adjustable crossovers on all channels HP/BP/LP/FP
12/24Db per octave selectable crossover slopes on all channels
Internal chassis force cooled speed controlled fan for optimum cooling
Hi/Low level balanced switchblade RCA inputs for maximum system integration
RJ45 Ethernet input connections for true balanced input connections
Block type terminal connections
256 color user selectable illumination circuit
Combined Bias circuit and temperature regulation circuit to regulate bias and lower THD at any point in total thermal cycle
Microprocessor high voltage power supply allows the amplifier to optimize power output at different ohm loads without the loss of efficiency or sound quality
Vdrive based preamp stage improves efficiency lower internal signal loss
Hand picked output devices used on all SE amplifiers.

Reviews

There are no reviews yet.

Be the first to review “Arc Audio Class A/B SE 2300 1300w 2ch SQ Audiophile Amplifier”

Your email address will not be published. Required fields are marked *